English Deutsch Français Italiano Español Português 繁體中文 Bahasa Indonesia Tiếng Việt ภาษาไทย
All categories

I had a leak near stove and I replaced stove hose but still smell gas.I did install a shut off and it is off for now. thanks!

2007-01-07 00:30:40 · 10 answers · asked by ktownandrew@sbcglobal.net 1 in Home & Garden Maintenance & Repairs

10 answers

Rednecks use a match.

For normal people, mix up a solution of dish detergent and water, brush it all over the connectors and if there is a leak it will blow bubbles.

I hope you used teflon tape or pipe joint compound on the threads when you installed the fittings.

Another possibility is that this could be a house fart.

2007-01-07 00:32:35 · answer #1 · answered by Kokopelli 7 · 1 1

You could disconnect the new hose from the stove and cap it off with a fitting designed to terminate the hose connection. Then turn the gas on again and use your nose to detect a leak. There's a safety valve in your gas pressure regulator valve that senses when the pilot or burner is lit or not. It must close automatically when all flames go out so that gas doesn't continue to be fed to the burners or pilot flame. So your regulator valve could be defective. A pressure test would show a leak down caused by the defective regulator.

2007-01-07 00:48:00 · answer #2 · answered by bobweb 7 · 0 0

Try the saop methods described above. If you do not find the leak and still smell it, call the gas company. This is potentially very dangerous.

If the smell is more than just faint, you should either shut the gas off or call the gas company immediately. This is nothing to play with.

2007-01-07 14:30:34 · answer #3 · answered by DSM Handyman 5 · 0 0

Use a mixture of dish soap (Ivory is the best) and water--about half and half is about right. Make a cupful and apply the mixture with a small paint brush, your fingers, or a small foam pad to all joints with gas pressure in them. As you apply it, look for bubbles and or foaming. If the smell of gas is relatively faint, you'll see foam, if the smell of gas is pretty strong you'll see bubbles and if it is REALLY strong (a bad leak) you may not see anything but the mixture being blown away from the leak and that's hard to spot.
If you have a lot of places to test (test EVERY joint even after you find one leak) a sprayer with the mixture in it will make the process much easier.

2007-01-07 00:37:46 · answer #4 · answered by DelK 7 · 1 0

Most hardware stores sell a suave that is thicker than soap and water and will improve you ability to spot the leak. I would try soap and water first (thick ratio) and then go to the store if you aren't successful. Also, remember to open the windows or ensure good ventilation while working.

Good luck

2007-01-07 00:36:31 · answer #5 · answered by stretch 7 · 0 0

Try a product called Snoop. This stuff works great, much better than soapy water...it's not too expensive either....check out the links below.

2007-01-07 00:52:11 · answer #6 · answered by GRANOLA 4 · 0 0

call the gas company

2007-01-07 00:32:20 · answer #7 · answered by MsFancy 4 · 1 0

they actually sell an item that detects gas..if your that worried go to supply store and buy one..

2007-01-07 00:36:08 · answer #8 · answered by Anonymous · 0 1

Call your gas company, don't mess with it yourself.

2007-01-07 00:39:22 · answer #9 · answered by F T 5 · 0 2

A match.



Okay, so........... soapy water.

2007-01-07 00:31:54 · answer #10 · answered by nope n 3 · 0 2

fedest.com, questions and answers