need a compresser to operate air nailers from a brad nailer to a 31/2 `` framing nailer..looking at a crafstman, 33 gal. - 150 psi. ??? anyone familiar with this compresser or a better suitable one ??? thanks.
2007-01-03 06:32:03 · 9 answers · asked by Anonymous in Home & Garden ➔ Do It Yourself (DIY)
You need to look at the horsepower rating of the compressor pump, and its rated CFM (cubic feet per minute) at a given pressure (PSI- pounds per square inch). The size of the tank is not so important. The capacity of the pump (compressor) which fills the tank is the key issue here. I would NOT recommend an oiless compressor because they have teflon piston rings which wear out quickly (compared to an oil-lubed unit) when subjected to regular continuous duty cycle use. Without further info, it sounds like the one you were looking at will do, depending on how many tools you will be using at one time. A roofing nailer will use more than a framing nailer because lots of nails are used in a short amount of time. A finish nailer will use less than either of the other two. Talk to someone who sells compressors and pneumatic tools and they should be able to set you up with the info you need. Once you know what you want, then shop for a good deal. Good luck.
2007-01-03 21:17:40 · answer #1 · answered by Peachfish Whiskerbiscuit 4 · 0⤊ 0⤋
I have a Hitachi portable that I use to run all of the tools listed. It’s small, portable and 10 Db quieter than a big 30 gallon unit. You only want to get the big units to run tools that need a lot of CFM (impact wrench / air sander / painters). You really don’t want to have to lug a big 30 gallon unit around a job site when a 5 gallon will do. You can’t run more than 2 framing nailers at once, but they work well. Stay away from Craftsman! There life time grantee does not cover power tools.
2007-01-04 05:36:05 · answer #2 · answered by Patrick D 1 · 0⤊ 0⤋
If you are only going to use one nailer at a time that compressor will do just fine. I personally use the DeWalt D55155 compressor, it has 2 outlets and is very portable, nice design, and I can even spray a ceiling with it!
2007-01-04 11:55:15 · answer #3 · answered by Anonymous · 0⤊ 0⤋
Oilless compressors are much MUCH louder than regular ones, be aware for indoor work.
A 33 gallon is not very portable. Sure you need that much?
The horsepower is more important than the PSI. Even a small one will provide as much PSI as you need. The horsepower is mostly important because it is directly related to CFM.
Also be aware of voltage. It is harder to find 230 volts on a job site.
2007-01-03 14:19:06 · answer #4 · answered by DSM Handyman 5 · 0⤊ 0⤋
get a compressor that can met the specs of the air nailer CFM and PSI get that compressor
2007-01-03 07:27:16 · answer #5 · answered by aussie 6 · 0⤊ 0⤋
I'd lean toward Campbell-Hausfeld. 33 gal is huge. Contractors usually use small portable models. Put the price difference on some air tools.
2007-01-03 07:42:31 · answer #6 · answered by Bill G 6 · 1⤊ 0⤋
Most contractors use "pancake" compressors or dual tank compressors for nail guns. They are light and easy to carry around (and they don't tip over easily) If you have a more permanent location for your compressor, you can buy a bigger one with a bigger tank. Get an oil cooled compressor for longer life.
2007-01-03 08:28:18 · answer #7 · answered by united9198 7 · 1⤊ 0⤋
In regards to the oiled compressor... If you are going to be using the compressor in a cold climate I would recommend a non oiled compressor. My oiled compressor will generally kick the breaker one or twice on really cold day before it decides to go... Just something to consider.
2007-01-03 11:47:16 · answer #8 · answered by David P 3 · 1⤊ 0⤋
I think that's a good choice.Plus Craftsman's has 100% satisfaction guarantee and there great about that ,just keep the receipt.And that should be plenty enough pressure.
2007-01-03 06:38:08 · answer #9 · answered by Anonymous · 0⤊ 0⤋