I have a 2004 Nissan 350z and the maintenance lights will come on every now and then when I hit a curtain mileage.
The maintenance light will stay on for a day and it will turn off automatically. You don't have to do anything but drive it and it will turn off. Hopes this helps =)
2006-12-03 18:52:16
·
answer #1
·
answered by Anonymous
·
0⤊
0⤋
350z Check Engine Light
2016-10-16 13:30:18
·
answer #2
·
answered by ? 4
·
0⤊
0⤋
Press the INFO button the MAINTENANCE INFO screen will be displayed.
To set the maintenance interval for the Engine Oil or Oil Filter choose an item using the joystick and push the PUSH ENTER button.
The Engine Oil/ Oil Filter screen will be displayed.
To reset, select the RESET key.
Set the distance of the maintenance schedule using the joystick. You can also set to display a message to remind you that the maintenance needs to be performed. The following example shows how to set the engine oil change interval. Use the same steps to set the other maintenance information.
Reset the driving distance to the new maintenance schedule.
Set the interval (mileage) of the maintenance schedule. To determine the recommended maintenance interval, refer to your "NISSAN Service and Maintenance Guide".
To display the MAINTENANCE INFORMATION automatically when the set trip distance is reached, highlight the "Display Maintenance Notification" key with the joystick and push the PUSH ENTER button.
To return the display to MAINTENANCE INFO., push the "PREVIOUS" button. Maintenance information display cannot be operated when the vehicle is moving. Stop the vehicle in a safe place to see the information.
Maintenance Notification
The "MAINTENANCE NOTIFICATION" screen ("ENGINE OIL" or "OIL FILTER") will be autumatically displayed as shown when both of the following conditions are met:
The vehicle is driven the set distance and the ignition switch is turned OFF.
The ignition switch is turned ON the next time the vehicle will be driven.
To return to the previous display after the "MAINTENANCE NOTIFICATION" screen is displayed, push the PREVIOUS button.
© 2006 ALLDATA LLC. All rights reserved.
Terms of Use
2006-12-03 18:20:38
·
answer #3
·
answered by russ G 3
·
0⤊
0⤋
If you are referring to the "Check Engine" light, it isn't a maintenance light. It is a warning to the driver that the compute has identified a fault or failure in one of the circuits or systems it monitors.
If that is the case, you really DO need to at least find out what it is reporting.
You can go to most discount auto parts stores, and the nice fellow there will usually retrieve the trouble codes, and many times offer an interpretation.
CAUTION -- Don't ASSuME that a code referring to a circuit necessarily means that the major component for that circuit is at fault. It may INDEED have failed, but run the diagnostics to confirm the fact rather than having to repair it again when the first job didn't do it.
Good Luck
2006-12-03 18:15:18
·
answer #4
·
answered by Ironhand 6
·
1⤊
1⤋
The methods mentioned are the only ways to remove the light. If you just can't turn it off with the scanner because you don't have one then goto an auto parts store like autozone and they will have it available to use. They don't charge anything to do it and you can have it read so you can know what it was turned on for in the first place.
2006-12-03 18:16:40
·
answer #5
·
answered by DW827 2
·
0⤊
0⤋
In terms of looks, 350Z blows away the S2k and RX.
How to turn off 'Maintenance Required" light:
1. Hold trip/reset button on dash
2. Turn key to "ON" or start engine
3. Hold button til light goes out
2006-12-03 22:04:59
·
answer #6
·
answered by Anonymous
·
0⤊
0⤋
If it is the maintenance required light then all you have to do is turn the key off, hold the trip reset button in and hold it while you turn to the on position *dont start it* keep holding the button til the light blinks and turns off. Hope that helps. Good Luck!!!
2006-12-03 18:19:25
·
answer #7
·
answered by TripleXXXrated 2
·
0⤊
0⤋
Don't know the year but with my experiance if it is 1993 or newer you have to use a scanner.
2006-12-03 18:17:52
·
answer #8
·
answered by mechy430 1
·
0⤊
0⤋
hold the reset mileage button for about 2 minutes. Thats for the maintanence reqired light which I believe is yellow in color.
2006-12-03 18:18:02
·
answer #9
·
answered by Star-Scream 2
·
0⤊
0⤋