My roommates and I bought a used washer/dryer combo for use in our rented home. However, the cord doesn't match the outlet. Here is a comparison pic I made: http://img230.imageshack.us/img230/1526/cordcomparisoncg5.jpg
Would it be easier (and safe) for me to change out the power cord? If so, could I just buy a new one from a hardware store? Or would it be better for me to get an electrician to change the outlet for me? Thanks.
2006-11-16 05:58:36 · 8 answers · asked by dood_lee 1 in Home & Garden ➔ Maintenance & Repairs
I would go with a electriican. If the cord dosent match your plug, It could be a different wattage.
I would not recommend touching electricity if you dont know what your doing.
Save yourself the pain and problems call an electrician!
2006-11-24 04:02:13 · answer #1 · answered by ohdarnitsmeagain 3 · 0⤊ 0⤋
There is only one correct answer.
Replace the outlet with the proper type to match the cord. There is a reason that the manufacturer put that cord on the device. The reason is safety. Don't bypass the safety feature by putting in some other cord that may or may not have the proper number and configuration of wires or may or may not be of the proper gauge wire.
Always de-energize the circuit before replacing an outlet.
Good luck.
2006-11-23 09:31:26 · answer #2 · answered by John S 1 · 0⤊ 0⤋
It would Be Easier To Change Cord. Go To Hardware Store Tell Them You Need 3 prong Dryer Cord.
2006-11-16 06:05:50 · answer #3 · answered by bob r 4 · 0⤊ 0⤋
The way i always do this job is to replace the"receptacle" with one that matches your dryer cord end. Draw a simple pattern of the cord end prongs. Go to a local supply store, i use Home Depot. They will gladly find the receptacle you need. It' rather simple to install, screw driver and needle nose pliers. Now the most important part of the job, and i cannot stress this enough!!!Be ertain the power is OFF!! If you cannot find the correct Breaker to turn off SHUT DOWN EVERYTHING!!! YOU ARE WORKING WITH 220 OR 240 VOLTS!!! After you finish the job do "NOT" turn the heater on until it is full of water or you will have to change the Heating Element inside the heater tank. If there is no water in the tank, the heating element will melt down. If you feel uncertain about the job, hire an exsperenced, licensed, Repair person to do the job for you. Better safe than Dead!!!!
2006-11-16 07:00:57 · answer #4 · answered by redbass 4 · 0⤊ 1⤋
It's better, cheaper and easier to just change the cord. You can get one that matches your outlet in any hardware or appliance store.
2006-11-16 07:19:08 · answer #5 · answered by Anonymous · 0⤊ 0⤋
you need a standard three-wire dryer cord. the cord on your dryer is a 4-wire type. the extra round pin is for earth ground. three-wire cords ground through neutral ( the middle wire "L" shaped).
you will need to reconnect the grounding strap (or wire) to the middle post also. The cord hookup is simple, middle wire to middle post, & either wire to either outside post.
2006-11-16 06:12:08 · answer #6 · answered by applpro 4 · 1⤊ 0⤋
one is a grounded 220 and the other is a plain 220 i would rewire the unit for the grounded 220 its much safer
2006-11-16 06:40:14 · answer #7 · answered by Anonymous · 0⤊ 1⤋
hey dood, be careful, shut off the breaker at the box and after you plug it in, go to the box and flip the breaker back on...if it blows, its wrong...if not yuo've scored.
2006-11-16 06:27:30 · answer #8 · answered by ticketoride04 5 · 0⤊ 2⤋