Do you know how to make a parol lantern?

Question

Looking for advice on how to make a parol lantern as well as on advice where to buy the materials (do regular arts and crafts stores sell the bamboo?).

I've already found some instructions from myparol.com, but unfortunately they don't specify the size/length of the material used to make a parol...and doesn't give much detail around how to decorate it.

Answer 1

Try this then :

- 10 strips of wood, 1/4 inch wide 10 inches long (or strip made from matte board, 1/4 inch wide and 10 inches long)
- 5 trips of wood, 1/4 inch wide, 3/4 inches long
- 2 12 inch squares of tissue paper, white and colored
- 2 8 inch by 16 inch pieces of tissue paper, white and colored
- 5 10-inch by 3-inch pieces of colored and white tissue paper
- 2 pieces of thin, flexible wire cut into 6 inch lengths
- 1 piece of thin, flexible wire cut into a 10-inch length
- construction paper
- foil
- non-toxic glue
- tape
- pencil
- ruler
- scissors
- markers
- glitters
- compass

Direction:

1. Make a star pattern, and glue five of the 10 inch strips of wood or matte board to make a star. Allow the glue to dry completely. Repeat with the other five strips. The two stars should be identical.

2. At the five points of one of the stars, glue the five 3/4 inch strips of wood so they are in an upright position. Allow glue to dry.

3. Place a dab of glue on the top of each of the shorter strips. Position the second star directly over the first one. Apply a bit of pressure at the joints to be sure they affix to the shorter strips.

4. To finish joining the stars, place a dab of glue at the five points of the star. Press together the points of the two stars. Use tape to secure the points until the glue dries. Remove the tape. Be careful not to pull the points apart.

5. To cover the star, place the glue on the surface of the outside strips (those that make up the points) on one side of the star. Position one of the 12 inch by 12 inch pieces of tissue paper on the side with the glue, so the star is centered on the paper. Keep the tissue as smooth and as tight as possible. Once the glue has dried, turn the star over, and repeat this step with the other 12 inch by 12 inch piece of tissue paper. Again, allow the glue to dry.

6. Trim some of the excess tissue paper, leaving enough to cover the sides of the star. Cut 7/8 inch slits in the joints.

7. Fold each flap over, and glue it to its corresponding wooden strip of the star. Once the flue dries, trim any excess paper.

8. While the star is drying, make the paper tassels. These look best if a different color tissue paper from that which covers the star is used. Fold each of the two 8 inch by 16 inch pieces of tissue paper so that the 16 inch length is in half. With the scissors, make cuts 3/8 inch wide and 6 inches long, leaving 2 inches at the folded side.

9. Open one of the tassels so that there is fringe at both ends. Fold the tassel in half length-wise, and squeeze both sides of the center. Poke one half of a 6 inch wire through the center of the tassel. Repeat these steps with the other tassel.

10. Fold the tassel in half so that all the fringe is together. Wrap the bottom half of the wire (that which is now covered with the fringe) around the area just at the top of the fringe. Repeat with the other tassel, using the second 6 inch wire.

11. Attach the tassels to the lower points of the star by poking the 3 inches of exposed wire through the tissue paper on the star.

12. Poke 2 inches of the 10 inch wire through the tissue paper at the top point of the star. Wrap the 2 inches of wire around the point, and wrap the end around the remaining wire. Use the 8 inches of wire left over to form a hanger.

13. To cover the wires of tassels at the bottom points and to put tassels on the other three points, fold in half each of the five 10 inch pieces of tissue paper. With scissors, make cuts 1/8 inch wide and 2 1/2 inches long, leaving 1/2 inch at the top.

14. To attach the tassels, spread glue on the uncut 1/2 inch area. Carefully, wind the glued end around each of the five points of the star.

15. Decorate the star using markers, glitters, etc.

16. Cut patterns out of construction paper, and glued them on the star. Make up a pattern. To do so, fold a sheet of construction paper in half. Copy the pattern onto the paper, making sure the fold on the paper corresponds with the fold on the pattern, and then cut the pattern out. Use a zigzag motion with the scissors to create a unique edge. Unfold the paper, and place glue only on the longer edges. Position the pattern on the star with the glued end toward the tassel. Repeat this step with the other four points of the star.

17. Paper scallop can be glued to the sides of the star. With a compass, draw a 4 1/2 inch circle on the construction paper. Cut the circle out, fold in half, and cut along the fold line. Fold the half circle in half four more times until you get a very small wedge.

18. Open the paper up, and refold using the fold lines to get accordion pleats. repeat these steps with nine more half circles of the same size. Glue one paper scallop to each wood support on all sides of the star. You may also make scallops using 6 1/2 inch circles. These can be glued between the smaller scallops.

Gud luck then..

Answer 2

can you give me sample on how to make christmas tree out of corn husk? thanks