Where on the boat is the stern?

Answer 1

::Stern::

The stern is the rear or after part of a ship or boat, technically defined as the area built up over the sternpost, extending upwards from the counter to the taffrail.

The stern area has always been the location of the steering apparatus (rudder, tiller, ship's wheel, etc), and by extension became the domain of the ship's captain and other officers. In particular, the stern was the location of the officers' quarters, and during the age of sail became the most opulent part of the ship, with rows of windows, galleries, walkways, and elaborate decorations. This resulted in a certain amount of vulnerability, and the goal of much maneuvering in battle was to achieve the stern rake, in which a ship would pour its entire broadside into the stern.

Other features of the stern included lanterns and the ensign.

In the early part of the 19th century, the stern of larger ships became gradually more rounded, and with the advent of screw-powered vessels, the stern became the location of the equipment, the officers moving elsewhere.

In modern cruise ships, the stern is frequently the location of the dining room, so as to provide uninterrupted views of the sea on three sides.


::Stern of Boat Picture::

http://www.cee.mtu.edu/boat/Stern_of_Boat1.jpg

Answer 2

The stern refers to the rear (or back) of the boat

Answer 3

The stern is the back of the boat where the rudder or transom are.

Answer 4

"Stern" refers to the back of the boat, as "port" refers to the left side, "starboard" refers to the right side, and "bow" refers to the front of the boat.

Answer 5

Back of boat

Answer 6

Stern is Rear, Bow is front, Portside, (facing forward) is left, Starboard, (facing forward) is right.

Answer 7

It's the part that leaves the dock last, unless you are backing out.

Answer 8

The end - the one that is flat as opposed to the bow which is shaped like a "V"

Answer 9

Stern to docking has many advantages over docking with the bow in towards land. In many boats, it's just easier to load gear and get on and off from the cockpit than over the bow. Although docking this way is commonly done, it's also common to see it not done, and not only for reasons such as protecting the rudder from grounding or hitting the dock, important though those are.


There are many reasons for not docking stern to, but one of the main ones is that it is difficult! I propose, in this short essay, to demonstrate why it is not more straightforward. You might pick up some tips which will help you to maneuver your boat backwards into its slip, or you may at least understand better when to try it and when not!

There is no shame in behaving prudently, and prudence often means doing things the easier way, or, more accurately, the more possible way. Most of us, even those who routinely dock stern to, have experienced dockages or weather in which even docking bow in stretched our skills and strained our cool reserve. I won't belabor this further, but even though it seems self-evident, remember to dock stern to only if you can.

Why does it have to be so hard? Many, but not all, boats steer poorly in reverse. There are many reasons for this, including very little water flow over the rudder, asymmetric propeller thrust (the sideways force exerted by the propeller, especially in reverse gear), which renders sternway steerage almost impossible in some boats, and the simple dynamics of the hull-water interaction, which work much better when making headway. If a wind is blowing, it frequently compounds reverse steerage problems, and a vessel which can be controlled in a fresh breeze when making headway may become less predictable when making sternway.

A simple trick to counteract asymmetric thrust is to use the propeller as minimally as possible. Get the boat moving astern just barely enough to enable the rudder to steer, and then go into neutral and drift backwards. It doesn't work for every boat, but it does for many.

Twin screws — Having and using the effects of twin screws can be a real boon under these circumstances. Even twin screws have limitations, but some vessels with them can even be made to walk sideways against a wind, given an experienced operator. I am going to leave the details for another time, and assume for the moment that you have a single-engine boat, as currently do I.

Contrariness — Another problem to overcome is that of “contrary motion and propulsion” — in this instance, I'm talking about using forward gear while you're still going backwards. Forward gear is commonly used when making sternway (briefly enough to allow the vessel to continue movement astern), firstly because steering is so much better in forward gear than in reverse (in many boats), and secondly as a means of putting on the brakes!

However, it gets more complicated than that because the concepts and techniques for “contrary steering” are completely different depending upon whether you're making sternway and then putting the boat into forward gear, or making headway and putting the boat into reverse gear. Again, I think it's too much to get into all of the niceties just now — we may get around to it eventually, and it's all in the book, but at least know that there's something to know!

Inboard or outboard? For steerage astern, would you rather have an inboard or an outboard engine? (Inboard/outboards are classed with outboards in terms of their steering mechanics.) Well, both propulsive designs have advantages and disadvantages, and for every boater who is sure he or she knows which one is best, another has a considered and differing position. In this instance, however, I vote for the outboard, because being able to actually swing the propeller itself from side to side affords better reverse gear steerage (acknowledging that there are always exceptions) than does a rudder. Do not construe this to mean that I prefer inboards, or outboards, or rowboats, or anything. My comments relate very narrowly to docking stern to.

Keels — Even more to the point, would you rather have a boat with or without a substantial external keel? As usual, there are pros and cons. For example, sometimes a full keel exacerbates the effects of asymmetric propeller thrust. Just as often, however, it allows the hull to track straight and true, and to tolerate a cross wind better, so in general, a boat with a keel will back into a slip better.

What to do? One solution for all of these things, as I mentioned above, is simply not to do it! Go in forwards. Many boating experts never dock stern to, or they manuever the boat only partly into its slip, and walk it the rest of the way in by hand. However, without going into all of the technical details, some of which have been discussed in this space before and some of which are planned for the future, another approach is to learn more about your boat. Practise backing into slips, starting in calm weather some place where there is lots of room for error. My hope is that it will be more rewarding and less frustrating for you if you at least know what you're up against, and why the boat doesn't just back up in a straight line when you engage reverse gear.

So, when practising sternway boat steering, consider all of the things we have touched upon: poor reverse steerage, asymmetric propeller thrust, adverse hull dynamics, wind, and contrary motion and propulsion. If you ever get it all figured out, please let me know, because I think you will be the first — this can be tricky, and I have met no one (myself definitely included) who couldn't still hone their skills a little more.

Conclusion — With practice and training, most boaters find that they rebel against their boats' idiosyncracies less and less, and learn to anticipate them and actively use them more and more. The boat may not not back up in a straight line, but you will learn how it does behave, and how it does respond to control inputs, and you will increase the likelihood of joining the elite club of “stern to dockers”.

The End

Answer 10

The blunt end