I have a Buick Regal 1998 and it seems like the cable that makes the window go up and down has disconnected. How do I get in there to fix it and then hook it back up?
2006-10-19 15:06:26 · 13 answers · asked by jerseygirl11964 1 in Cars & Transportation ➔ Maintenance & Repairs
First off, the window doesn't work on a cable. If you have electric windows the moror either burnt itself out or you have a disconnected wire somewhere in the circuit. If it's a mnaual window (crank style) it operates on a gear and slide rail to which the slide track is probably worn out allowing it to either jump or become stuck in the worn area.
You have to remove the handles and all the screws in the door panel, then there are also push pins that you pry out from the back of the panel. If you've never done it before I suggest you go to your local auto glass shop for service!
2006-10-19 15:12:58 · answer #1 · answered by Anonymous · 1⤊ 1⤋
My husband is very handy, so when our window went out on our 2002 Dodge Caravan, he took the side panel off, and couldn't believe how involved it was. He couldn't do it. We ended up calling a guy who specialized in fixing them, and it was quite a project. He had special tools, and we never would have been able to do it. Also, you can't buy just the motor. You have to get the entire cable assembly that goes with that window. Leave this job to the experts. It was about $250 per window, but they were guaranteed and he did a wonderful job.
2006-10-19 15:12:01 · answer #2 · answered by Momma Jo 6 · 0⤊ 0⤋
If you have power windows, they are operated by DC (direct current) motors. These motors use(carbon) brushes and they wear out. If you can remove the inner door panel, try tapping on the motor while you hold the switch on to move the window. If it moves, most likely the brushes are worn or the armature is dirty. (Brushes most likely) That is only one type of test to see if it is in some other part of the system. Granted, it doesn't always work, but I have used this method and it has worked for me.
Good luck
2006-10-19 15:24:27 · answer #3 · answered by Donald S 2 · 0⤊ 0⤋
if the cable has disconnected you more than likely need an entire window regulator assembly, this is because the cable snapped, not disconected. sometimes the motor has to come with it, that is the trend in auto manufacturers today, making everything one piece speeds up assembly.
i know for a fact that this is what needs to be done in a jeep grand cherokee, it is a common problem.
2006-10-19 15:23:29 · answer #4 · answered by Anonymous · 0⤊ 0⤋
LOL. This sounds like one of the old "Blond Jokes" of the 1970s However, after reading the problem over and over and over again I finally get it! ... She needs to get INSIDE the actual door panel to locate the cable to fix it.
Sorry I can't help but thanks for a good chuckle.
Guess I'm a bit of a Blondie myself - LOL.
Cheers and Good Luck.
2006-10-19 15:20:59 · answer #5 · answered by rentongal1958 3 · 0⤊ 0⤋
Take the door panel off
2006-10-19 15:09:46 · answer #6 · answered by Granny 1 7 · 0⤊ 0⤋
Actually, the switch itself is probably at fault and needs to be replaced. Unless you want to purchase body tools, just pay a mechanic to take the door panel off.
2006-10-19 15:09:12 · answer #7 · answered by MissAnthropic 2 · 0⤊ 2⤋
yopu probably don't have a cable but you start by taking off the door handles and the inside door covering. have fun its a bear.
2006-10-19 15:15:25 · answer #8 · answered by roy40372 6 · 0⤊ 0⤋
took mine to the dealer and cost a buck to fix a faulty wire. Hope that helps
2006-10-19 17:42:15 · answer #9 · answered by trigunmarksman 6 · 0⤊ 0⤋
put the key in the keyhole and turn the key. Then lift the lever and pull the door ajar. If you can't open the door you'll never figure out the window mechanisms, much more technical.
2006-10-19 15:09:55 · answer #10 · answered by Anonymous · 0⤊ 4⤋