How do you take out a light bulb that the whole glass end blew off and only the metal bottom is left?

Question

I dont have a potatoe, and is it okay if I just turn the power off?

Answer 1

yeah as long as you are sure the switch is in the off position youll be fine. ive been shocked by 110 volt which is what your light is and it doesnt kill you. as long as the light is off you will be fine. if there is a fan attached make sure that the power is off by turning on the fan and hitting the switch to shut it off. then just take it out with a plier.

Answer 2

First, turn off the power by flipping the circuit breaker.

Take a pair of pliers and grip the rim of the bulb's metal base. Keep your pliers straight so you don't twist and bend the thin metal. Wiggle the pliers back and forth to loosen the bulb base in the socket. When you feel it move, then turn it counter clockwise (anti-clockwise) to remove the broken bulb.

Be careful with the thin, fragile glass shards. You can get a nasty cut.

Next time, purchase more expensive bulbs. In my experience the cheaper bulbs tend to burn out quicker and separate from the metal bases more readily. Also, if the socket is metal instead of ceramic, the metal bulb base and metal socket tend to heat up and almost glue themselves together, making it more likely the glass will separate from the metal base when the bulb burns out.

Answer 3

First, disconnect the lamp from the electric powered furnish (unplug the lamp, or turn off the circuit breaker, or eliminate the fuse). Use something of the right length & consistency so as that one end of this is going to snatch the damaged base of the bulb, and the different end will in advantageous condition conveniently on your hand. as an get mutually, a potato or a chunk of smooth timber (you would possibly want to opt to trim the top that is going into the socket). With a trash receptacle positioned below the lamp, press this merchandise into the socket, unscrew the bottom of the bulb, and drop the finished mess quickly into the trash. you are able to opt to comb out perfect slivers of glass from the lamp. P.S.: this is tempting to attempt to apply pliers to curl out the bulb base, notwithstanding this is demanding to unscrew the bottom that way and also you would possibly want to likely spread extra glass round.

Answer 4

Make sure it is off, and if possible check with a voltmeter or voltage detector. Although the light switch should interrupt the hot wire to the light, it is possible that someone wired it incorrectly. If you can't be sure, turn off the breaker that supplies the light.

Get a pair of pliers, preferably with insulated handles just in case, and grab the edge of the metal part; you might have to bend it in a little to get a better grip. Now you should be able to twist the metal base out.

Answer 5

Turn off the switch, throw the related circuit breaker off. With needle nose pliers grab the bulb base and twist it to the left to remove.

These days the threaded receivers into which bulbs are screwed are made of cheap metal or ceramic and have a high friction quotient, making it difficult to screw the bulbs in or out. To avoid the problem in future place a dab of petroleum jelly at the bottom of the bulb threads before screwing in to the receptable.

Answer 6

Turn the power off and use a plier to bend the metal enough to get a grip on the bulb.....or use a potato.

Answer 7

Turn off power. With both hands--insert a pair of plyers in the light bulb base--pull outward on the plyer handles and twist the broken light out.

Answer 8

Turn off the power first. Use a needle-nose plier, either to grab onto the metal rim, or put it inside the unit and expand the jaws to exert pressure while you unscrew it.

Did I mention that you should turn off the power first?

Answer 9

Pliers, try to grab a hold onto the metal part and turn. Or, use a half of a potato, just cut one and shove it up there and turn.

Answer 10

they are all good answers, but remember, if you cant find the right breaker, simply turn off the main breaker(the big one on top) you will have to reaset any clocks, but you are sure to have the power off. if you dont have pliers, simply use a rag or a sock to reach inside the metal part and twist it out.