What is the best way to wire for 240V downlights. I want 6 lights wired into a single switch.
2006-10-06 00:04:16 · 12 answers · asked by Sammy K 1 in Home & Garden ➔ Do It Yourself (DIY)
I'd create a loop for the 6 lights (like a ring main), supplied from the single light switch (fused) ensuring the cables can cope with the load from each light individually. This ensures even power distribution. Make sure the cables are properly secured and mechanically protected. Use a single feed supply to a junction box near where the lights are to be installed. You can then loop off this one (rather than from the light switch - not a good idea)
2006-10-06 00:07:50 · answer #1 · answered by Charlie Brigante 4 · 0⤊ 0⤋
The max wattage of a downlight is 50w, so only 300w max for all 6. Def use a junction box for all terminations, connectors are dangerous. You can do it yourself in accordance with the new regs, unless it is in a "special location" which is a kitchen or a bathroom. Those locations must be certified, so you need an electrician.
2006-10-06 21:41:06 · answer #2 · answered by andygos 3 · 0⤊ 0⤋
There is not best way, just a correct way. If you don't know that correct way, I would ask for an electrician's assistance. As far as 6 lights on a 240V ciruit, that load is very low at 240V, so don't worry about that.
2006-10-06 00:51:31 · answer #3 · answered by novamanassas 2 · 0⤊ 0⤋
Tread carefully; all new electrical work is now required to be signed off by a qualified electrician, (Which, in practise means installed by same) Also, you probably don't have the knowledge to work out cable & switch loadings + a host of other safety requirements.
2006-10-06 00:27:26 · answer #4 · answered by Anonymous · 0⤊ 0⤋
Use a terminal box wire all lights separately, add your live feed, and your switch wire, connect all blue wires together, your brown from your feed goes with the brown of your switch and the other brown of your switch goes with all the browns of your fittings.Then all Earths together on there own
2006-10-06 00:13:52 · answer #5 · answered by bty937915 4 · 0⤊ 0⤋
If you've got 6 lights fed from one switch you may also have to consider downrating the bulb wattage. Check that the switchplate you intend to use can take the load of what you're putting through it !
2006-10-06 00:16:42 · answer #6 · answered by Jon H 3 · 0⤊ 0⤋
Use 2 transformers (or one if it's big enough) and power the transformers from the wires leading to the existing lamp holder.
2006-10-07 02:55:38 · answer #7 · answered by grammyammy 2 · 0⤊ 0⤋
Get an electrician in. Seriously, it is far too dangerous to be messing with it yourself. I have done loads of DIY in my time, but when it comes to electricity, I leave it to the experts.
2006-10-06 00:13:04 · answer #8 · answered by Emma W 4 · 0⤊ 0⤋
WIRE TO A CENTRAL JUNCTION BOX AND WIRE OFF THIS
YOU ARE BETTER OFF USING 12V WITH A TRANSFORMER IS POSSIBLE
2006-10-06 00:13:19 · answer #9 · answered by RAMSBOTTOM 5 · 0⤊ 0⤋
hire a licensed electrician
2006-10-07 16:13:45 · answer #10 · answered by pahump1@verizon.net 4 · 0⤊ 0⤋