Leaky Outdoor Spickets?

Question

All of our faucet spickets leak terribly when a hose is attached. Water spews everywhere instead of down the water hose and onto the lawn. What can we do?

Answer 1

Either the hose connection is damaged (not round) or the hose washer is worn out. If the water comes out of the valve you need to replace the washers in the valve. Be sure that you turn off the main water valve before removing the faucet handle.

Answer 2

If you shut the water off to the spigot, there's a valve stem that's held in it with a nut. If you remove it and take it to a hardware store, they can match it up and sell you a new one. Just put it in the same way you took the old one out. Then turn the water supply back on to the spigot. The rubber gets old and water leaks by after a few years. Hold the spigot as you turn the nut, so the pipe doesn't get twisted. That's if the spigot leaks. If the hose leaks at the connection, the washer's missing or old. Just replace the washer. Sometimes the brass can wear between the hose and connection. A new hose is the only way to fix that one.

Answer 3

The answere to your question all lies within where the actual leak is comming from. If the water is coming from between the hose and the faucet then you need to replace the "hose washer". I suspect you may have a different problem from the way you described it. It sounds like to me that you have a what is called a frost-free sillcock with an anit-siphon on the top of it. These work great in the sense that they keep you from getting flood damage in your home, but often the anti-siphon cracks. When this happens the water pressure takes the path of least resistance through the cracked anti-siphon and spills out. The anit-siphon componets can be replaced most of the time. Most plumbing supply houses carry these. I would actually suggest replacing the whole sillcock if there is easy access being that it often costs less than a rebuild kit.

Answer 4

Go to the local hardware supply, and get a set of hose washers. They are just "O" rings to create a seal between fittings. If on the other hand, the faucet is turned off yet still leaking, you probably need a new seal in the fixture itself. Any hardware store assistant can determine what is needed.

Answer 5

Rubber washer
you need to insert a rubber grommet in the end of the hose before attaching it, that is if the hose itself is not leaking
buy a new hose

Answer 6

check to see if the rubber washer is in the end of the hose, if so youneed to replace the spicket

Answer 7

have you replaced the rubber washers?

if so, the connector at the end of the hose may be worn.
they can be replaced, but may be better to get another hose for those "spigots".

Answer 8

the finest mind-set is to position in a 'T' installation the position the significant water grant comes up, purely formerly it enters your position. you've the alternative of operating from there to the nearest outside element, or someplace in direction of your backyard. on the 'T' installation i'd advise installation a capped adapter, or spigot, as well because the spigot you want on the finest.... this would make it extra accessible to empty for the wintry climate. i take advantage of a capped adapter myself, after a close off valve, so i am going to blow the line empty, with my air compressor even as winterizing. Your different selection is to tap into the the plumbing contained in the area between the underbelly, and the floor joists. i'd upload a litte extra insulation to the area, if going this kind, to help dodge freezing of the pipes - and be particular to apply between the 'freeze evidence' spigots (an extremely lengthy spigot that actual shuts off about a foot back from the spigot outside). you'd be intending to drill a hollow contained in the rim joist for this way of installation. both approach will value about a similar in aspects. have exciting

Answer 9

I hate drippy hoses! Try a rubber washer.

Answer 10

is the rubber washer missing from the end of your hose?