It sounds like you did a good job of trouble-shooting the equipment. When you say the pressures are o.k., that indicates to me that your refrigerant is at the proper level.
Given that the gas is o.k., there are two big reasons for your problem to occur. One, a duct that has worked its way loose, or two, undersized equipment. The reason I think it may be undersized is that your question seems to indicate that it works o.k. when it is cooler out.
You should have at least 12,000 b.t.u's (1 ton) of cooling capacity for every 500 feet. A 1500 square foot home under air typically would have a 3-ton unit. This can vary widely with extremes of glass area and r values of insulation. Bear in mind that tonnage also refers to the cubic feet per minute produced by the air handler. A unit that is undersized will not only short you on cooling b.t.u.'s, but air flow as well. If your air is trickling meekly from your vents, I think we can assume undersized equipment.
If you are not prepared to upgrade the equipment and ductwork, you can consider (at least in the short run) augmenting the cooling b.t.u.'s with window units. (cheaper, but not terribly efficiant.)
One last thought. Sometimes the heat strips will kick on during the cooling cycle. Make sure this is not the case.
2006-07-26 12:49:11
·
answer #1
·
answered by Elwood Blues 6
·
1⤊
0⤋
How did you determine your refrigerant level is "ok"? If it truly is, your a/c WILL run constantly when the temp is 95f , because that is the high end of the design temp. But, if its not maintaining temp in the house, check your duct for proper insulation (ESPECIALLY if return runs in the attic), and make sure your supply and return grilles are not restricted / blocked. A simple test that you can do to test your systems efficiency is to check the supply air temp vs. the return air temp. You want a 15-20f difference between the two. If there isn't a sufficient temperature difference, your unit may not be performing properly, or back to the duct investigation.
2006-07-26 17:51:38
·
answer #2
·
answered by Anonymous
·
0⤊
0⤋
i will assume the technician actually knew the thanks to analyze the freon aspect. it really is questionable and that i ought to easily call them lower back and scream at them and demand both a reimbursement or a splendid diagnosis. in case your AC unit had frozen up it ought to were very glaring to him. An AC unit will merely freeze up from 3 circumstances. First - ventilation(grimy clear out, clogged coil, undesirable blower, and so on) second - low freon, 0.33 - undesirable enlargement gadget(enlargement valve or orifice). All of those ought to were glaring if he had actually checked the indoor unit and refrigerant fee. So assuming the tech knew what he develop into searching at (and that is a huge assumption), i ought to trust you've a vent off or tremendous hollow on your ductwork that needs patching. A duct situation ought to ought to represent you're dropping countless your AC air in an attic or crawlspace it really is the reason it ought to no longer save up.
2016-11-26 01:38:02
·
answer #3
·
answered by Anonymous
·
0⤊
0⤋
It may be that it is froze up on you. Try to turn it off and let it sit for a while to thaw. If that is it then do not set it to such a low temp. It will ask to much, make it work to hard and then freeze up again. There is no way you can check your own freon. It takes a machine that removes it weighs it to see how many pounds were in it and if you were low. You need to take it in or have someone come to you to repair it if it is not froze.
2006-07-26 12:34:33
·
answer #4
·
answered by tamiandjerry 2
·
0⤊
0⤋
Low BTU capacity for the room to be cooled or bad thermostat.
2006-07-26 12:43:31
·
answer #5
·
answered by Handyman 4
·
0⤊
0⤋
Check your freon. But make sure you hire a technician to refill it.
2006-07-26 12:31:24
·
answer #6
·
answered by Anonymous
·
0⤊
0⤋
check freon?
2006-07-26 12:29:37
·
answer #7
·
answered by kcracer1 5
·
0⤊
0⤋