I have tried numerous products with some success but there's still some mold that can be seen in the grout as well as on the floor of the shower.
2006-07-10 09:09:47 · 10 answers · asked by Lynnie 2 in Home & Garden ➔ Cleaning & Laundry
I use Lysol Mildew Remover With Bleach. I just spray it on and let it sit for several hours, then spray on some more (if needed) before I wash it off. It works really well for me. If the mold is too deep in the grout, then it probably would be best to replace the grout. If you use the Lysol spray once a week the mold never gets the chance to build up, so it will never become a problem.
2006-07-10 12:50:02 · answer #1 · answered by Jeannie 7 · 1⤊ 0⤋
First off, you didn't say what type of grout and what type of wall so I will take a crack at this without knowing. If mold has gone beyond the grout it will be impossible to for you to tackle without removing the actual grout itself. Bleach can be used in well ventilated areas but be careful not to ruin the other surfaces in your shower.
Here is what I have done in the past at customers homes when they have had mold issues.
1.) Make a paste from any abrasive cleaner. I like Comet myself.
2.) With small brush or even an old toothbrush clean the areas with the mold and let sit for an hour or so.
3.) Rinse and shine.
If you see any signs of improvement you can continue to do this until the mold is gone. If it doesn't help then you will need to have your grout replaced. The above process will also brighten any ceramic tile or fiberglass shower floor.
2006-07-10 11:19:48 · answer #2 · answered by bethany g 2 · 0⤊ 0⤋
I am suspecting something other than surface mold at this point. It is time to consider that water may be lurking behind your walls and in your shower pan. The reason it is important to rule this out is because of the types of fungi that can proliferate in situations with long-term leaks, including stachybotrys, which can produce a very problematic gas, or mycotoxin, that is tough on the nervous system.
Remove the grout (a simple grout saw will do) and carefully pop out a tile in the worst area and see what's going on. Wear a respirator with decent biological cartridges.Better safe than sorry!
2006-07-11 07:30:10 · answer #3 · answered by Elwood Blues 6 · 0⤊ 0⤋
Until I gave in and replaced the grout, I used bleach. I unrolled cotton balls into long thick strips. I think dipped them in bleach and laid them along the grout lines. I even left the ends dry and used masking tape to do the up and down grout lines. I left it there at least an hour.
2006-07-10 13:50:20 · answer #4 · answered by Amy Y 1 · 0⤊ 0⤋
Bleach will do, if you can get the liquid to remain in place. Otherwise, I use Ajax. I moisten the walls, scrub Ajax into the grout (it has bleach in it) and let it stand for a while, then scrub. You may have to repeat. Tilex will work well but only after you do a thorough cleaning first. Tilex will help keep it clean.
2006-07-10 09:20:03 · answer #5 · answered by AnOrdinaryGuy 5 · 0⤊ 0⤋
Bleach will usually do it. If not, then the stuff has gotten underneath the grout and you will have to scrape it out and regrout those areas.
2006-07-10 09:13:37 · answer #6 · answered by Anonymous · 0⤊ 0⤋
The Clorox Pen works when straight bleach does not, because it is a thick gel and will cling the surface and continue to bleach until you rinse it off. Also, CLR works pretty good.
2006-07-10 10:28:21 · answer #7 · answered by DeeDee 6 · 0⤊ 0⤋
X-14 if you can find it! Home Depot is a good source.
2006-07-10 09:52:46 · answer #8 · answered by jagerbombmeister 3 · 0⤊ 0⤋
you can scrub with bleach or if you want to be safe for the enviroment mix "BAKING SODA with WATER"
2006-07-10 09:13:34 · answer #9 · answered by Samuel W 1 · 0⤊ 0⤋
bleach will do it.
2006-07-10 12:45:01 · answer #10 · answered by whichwayisup 2 · 0⤊ 0⤋