how do i do a textured ceiling?

Answer 1

There are 2 ways. One is to spray a sort of textured foam on the ceiling before painting it. This will give more of the 'popcorn' effect. The other way is to apply the paint with a sponge and 'dab' it on instead of spreading it on.

Answer 2

Some of these answers are correct. If, on the rare chance this is new construction and you are laying plaster walls rather than wall board, then you CAN sculp ridges and designs into your ceiling while the plaster is being put on. You can also sculp designs into plasterboard with a finishing plaster.

Spraying foam is a mess - doable, but not recommended.

The traditional way is to buy "texture" and mix it into the paint prior to painting. Then use a fine roller and roll on the textured paint. The texture is a chemical sand that expands and adheres when in contact with the paint. I've used this for a number of clients and had good results.

Beware of two things though: 1)once the wall is textured, it will "always" be textured, unless you invest in days and days of labor to smooth it out; 2)experiment with the amount of texture, if you use the mixing recommendations that are on the texture cartons, most people want "more texture". I've actually used 4 to 6 times the recommended amount to get the coverage that clients expect.

Good luck.

Answer 3

Texturing a ceiling can help hide imperfections and create a new look. Blown-on texture is one of the easiest and least expensive way to spruce up a room's "fifth wall."

Get Ready

Steps:
1. Measure the room to determine the ceiling's surface area. Include any alcoves, hallways or closets that are part of the project.

2. Take these figures with you to the home improvement store, lumberyard or rental center and let the dealer determine how much texture mix you need, considering the ceiling's surface area and the mix you decide to use. Remember that it is better to get a couple extra bags and return them unopened than to run out.

3. Choose your texture mix. Texture generally comes in a small, medium or large "grain" - your dealer will probably have some samples to look at. Some textures even have sprinkles of glittery color to dress them up.

4. Rent the machine to apply the texture - usually from the same place you bought the materials. Some stores will even let you use the machine for free when you buy materials from them.

5. Get a thorough demonstration from the dealer on the setup, use, disassembly and cleaning of the machine.

6. Move as much furniture out of the room as possible and cover anything left with tarps or plastic sheeting. Cover all floors as well.

7. Cover at least the upper three feet of all walls with sheets of plastic. You can secure the plastic with tape or carefully staple it in place.

8. Remove any ceiling-mounted light fixture covers. Protect any hardware left in place with plastic and tape.


Tips:
Stapling the plastic to walls is a method that is quick, easy and effective, but only do this if the walls are to be spackled and painted later.


Prep the Texturing Product

Steps:
1. Make sure that you have the machine set up according to the dealer's demonstration before you begin mixing. (If possible, leave the machine itself outside the room being textured so that the overspray won't fall on the machine.)

2. Mix the texture in a five-gallon bucket if you're working in one room only. For a large room or series of rooms, a large, clean, plastic trashcan will do the job.

3. Dump several bags of the texture into the trashcan and start adding water according to the manufacturer's packaging recommendations. Generally, you want to achieve a runny oatmeal consistency.

4. Mix well with a 3-foot piece of scrap 1-by-2, or (ideally) use a power drill with a mixing attachment. Well-mixed texture will ensure an even, trouble-free finish.


Spray on the Texture

Steps:
1. Fill the hopper of the machine with the premixed texture. (Don't overfill or you may end up wearing more than you get on the ceiling.)

2. Pick an inconspicuous spot to try out your technique. (Closets work well for this.) Then move to the main part of the room.

3. Keep the sprayer the same distance from the ceiling (usually 12 to 16 inches) and use an even stroke. Maintain a consistent rate of travel as much as possible.

4. Texture around the entire perimeter of the room first and concentrate on a controlled spray near the walls. This cuts down on the overspray and minimizes cleanup.

5. Work from one end of the room to the other. Go light on your first pass while you get a feel for the process.

6. Let your first coat dry a few minutes.

7. Fill in slight depressions or feather out bulges on subsequent passes.

8. Begin cleanup on the machine according to the dealer instructions as soon as you are satisfied with the ceiling.


Tips:
This is not a tidy process. Make sure you are wearing goggles and dust mask.

The texture isn't chemically harmful, but it can be uncomfortable if your eyes or nose get gummed shut with overspray. Use soap and water to clean up.

For spills, warm soapy water and a sponge or rag will suffice.

If you have several ceilings to texture and plan to keep the machine overnight, make sure you clean it before you stop for the night or for lunch or long breaks.

Answer 4

If its for a home, textured paint should do the trick. There are special rollers that have heavy textures to it, and the paint used for this purpose is thicker than the usual paint.

You may also use multi-color paint. The ceiling is usually coated with a layer of flat paint. A second layer of special multicolor paint (deeper tone) is sprayed on to the flat paint surface, thereby creating a speckled textured look. The density of the multicolor paint may vary, depending on your preferrence.

Answer 5

You an purchase a machine that 'blows' texture onto the ceiling or you can use a special typr of roller. The best thing to do would be to attend one of those classes at Home Depot or something. That way you can get some hands on experience and expert advice prior to attempting such a job on your own.

Answer 6

There are different types of Texture, if you mean Acoustic- you will need to rent a machine to blow it on, - other Texture is called Crowsfoot, Stomp, swirl, etc. You make that by reducing drywall mud to a spreadable consistancy then brush on or spray, then Stomp with a Brush with a Handle. They make some Boxed Texture also, - never used it.

Answer 7

It depends on what texture you want. The cans of paint say if you want a slighty textured finish put sand in the pain mixture. This is the cheap alternative.

The expensive alternative is to have textured wall board installed in your cieling.

Answer 8

Don't do it. People hate those popcorn ceilings and it will be hard to sell. Paint it a pale color instead.

Answer 9

if you have never done it yourself i would recommend that you hire someone to do it... mainly a drywall contractor. the first time i did it was in my bathroom and it came out lumpy in spots... luckily i was able to hide it with a few coats of paint... if its a small room you might try it yourself but if there is alot of foot traffic i would recommend that you hire someone to do it for you

Answer 10

When you put up the plaster, use brushes and sponges and whatever you want to create designs.