"How the heck do you tie a tie?".......?

Question

OK....... I bought my hubby a tie because we are gonna be going somewhere that he will need a tie, and........ I don't know how to tie it..... Help PLEASE.........

Answer 1

Go to this website: http://www.scoutdb.org/h2tat/

Hope this helps. Good luck.

Answer 2

Windsor Knot

The Windsor Knot is a thick, wide and triangular tie knot that projects confidence. It would therefore be your knot of choice for presentations, job interviews, courtroom appearances etc. It is best suited for spread collar shirts and it's actually quite easy to do.

While just about everyone can use this tie knot to tie his tie, it looks especially well on men with longer necks as its wide form shortens the perceived height of the neck a little bit.

To tie the Windsor Knot, select a tie of your choice and stand in front of a mirror. Then simply follow the steps below:




1) The wide end "W" should extend about 12 inches below the narrow end "N". Cross the wide end "W" over the narrow end "N".





2) Bring the wide end "W" up through the loop between the collar and your tie; then back down.




3) Pull the wide end "W" underneath the narrow end "N" and to the right, back through the loop and to the right again so that the wide end "W" is inside out.





4) Bring the wide end "W" across the front from right to left.





5) Pull the wide end "W" up through the loop again.




6) Bring the wide end "W" down through the knot in front.



7) Using both hands, tighten the knot carefully and draw it up to the collar.




Congratulations, you did it! You see, it is not rocket science after all. Simply keep practicing the Windsor Knot a few more times until you can tie this necktie knot within less than 30 seconds.

Good Luck Hope this helps

Answer 3

Ok first put the tie around the neck. Then take the bigger end that will be showing down until the smaller end is about 3/4 the distance of the big part. THen wrap the big part of the tie over the smaller part. Bring the big part up through the hole created between the neck and the wrap. Place that part through the wrap and then down through. Pull the small end to tighten the tie.

Answer 4

Okay have him hang the tie on his neck then put the large end over the small end. Then loop the large end around the small once. Then pull the large end up through the back and slide it through the hole thats created by the loop. Then just pull tight.

Answer 5

1. drape the tie around his neck with the fat side on the right and the thin side on his left. Keep the thin side about even with his breast.
2. take the fat side and wrap it twice around the thin side
3. take the fat side and loop it up underneath
4. put the fat side through the front slot made when you first wrapped.
5. take the "neck not" you've now formed and pull it upward while pulling the fat part of the tie downward.

You may have to resize.

Answer 6

I am sorry.. I just want to you to know that I answered.. but I am probably no help with you to this Q I have seen ppl ask about othe ppl a lot and i have often wondered the same thing!! But unfortunately i have never seen "BUK" So sorry I am sure one of your answers explains it though!!! Best of Luck!!! Olive

Answer 7

The following site explains how to tie a tie: http://potterties.com/how-to-tie-a-tie

Answer 8

around... around... up... and down. Cross over the front first with the large end and do this twice. When you come up with the large end, come up through the back, and go down through the little loop in front and pull tight :)

Answer 9

wide side on the left, hanging a little lower than the thin end. wrap left side across the right, under, back to the left, pull up, tuck through knot!! good luck i hope that helps!!!

Answer 10

Next time buy a clip on, all my ties are clip ons because I don't know how to tie a tie.

Answer 11

no